Skip to content

We measure every opening at your free in-home estimate: (626) 654-3121

(626) 654-3121
Installer in a tool belt adjusting the top track of a black multi-folding glass door, panels stacked at one side, on the back wall of a stucco house opening to a patio

ServicesMulti-Folding Doors

Multi-Folding Doors in South San Jose Hills

Swap a solid wall or tired slider for glass panels that fold back and leave the room wide open to your yard. We size the header, set the track level and seal the sill, so the door glides with one hand and keeps the weather where it belongs.

What a Multi-Folding Door Is and When It Fits

A folding door is a row of glass panels hinged together on a single track. Slide them and they stack up against one side, like an accordion closing. Folded back, they clear most of the wall. Closed, they give you a wide glass wall that locks.

It makes sense when you want to step from the family room to the patio without squeezing through one narrow door, and the wall is wide enough to allow it. Most of our jobs start with an old slider or a solid stretch of wall that we open up. A lot of houses around here are single-story ranch homes on a slab, which tends to work well for this kind of door. We still look at the wall first, because the load above the opening sets the limits.

We are CSLB C-17 licensed and have run this business for 12 years. If your wall is a poor match for a folding door, we will tell you, and we can talk about sliding door replacement instead.

What the Job Includes

Measuring and a wall check

We measure the rough opening at several points and check it for level and square. We also look at what the wall carries, so we know early if the header needs to change.

Header and framing work

Folding doors hang weight across a wide span. If the opening gets wider, the header has to be sized so it does not sag and bind the panels. We frame it to the size the plans call for.

Track, sill and panel setup

We set the sill dead level and shim it on solid support. Then we hang the panels, adjust the hinges and rollers, and run the door open and closed until it moves with one hand.

Sealing and flashing

The sill gets pan flashing and sealant, and the sides tie into the stucco or siding so rain and wind-blown dust stay outside. Interior trim is finished at the end.

Haul-off and cleanup

We take away the old door or wall material and sweep up. Your floors near the opening are covered while we work.

Signs a Folding Door Makes Sense

  • Your old slider sticks

    Sliders with worn rollers drag and jump the track. If you are replacing it anyway, a folding door may open far more of the wall for the same space.

  • The room feels closed in

    A family room with one small door to the yard can feel dark. A folding door brings in light and lets you open the whole side on a nice evening.

  • You live outside half the year

    Long, warm seasons mean the patio gets used a lot. A wide opening makes carrying food out and keeping an eye on kids much easier.

  • Drafts and heat at the old door

    Single-pane glass and tired weatherstripping let summer heat pour in. New folding panels come with dual-pane, low-E glass and fresh seals.

  • You are planning a remodel

    If walls are already being opened, it is a good time to frame for a folding door. Doing it later means opening the wall twice.

From First Visit to Final Walkthrough

  1. 1

    Free in-home estimate

    We stop by, check the wall and take measurements. You get a written estimate that lists each part of the job, with no sales pressure and no obligation.

  2. 2

    Permit and ordering

    Changing a wall opening usually needs a building permit, and we pull it. Each folding door is made for its own opening, so we order only after the sizes and the header plan are final.

  3. 3

    Opening and framing

    On install day we cover the floor, remove the old door or wall section and set a new header if the job needs one. At the end of each day the opening is closed up or covered.

  4. 4

    Hang, adjust and inspect

    We set the track, hang the panels and fine-tune each hinge and lock. If the permit calls for an inspection, we book it and meet the inspector on site.

  5. 5

    Walkthrough

    We show you how to fold, lock and clean the track. Then we haul away the old material and leave the room swept.

Cost Factors for a Folding Door

Every folding door is built to fit one opening, so the price follows your wall and your choices. The width you want, the work above the opening and the door itself make up most of the total. We see the job in person before we put a number on it, and the written estimate breaks out each part.

Width and number of panels
A wider opening takes more panels, more hinges and rollers, and more glass. Extra height adds to the build and to the work of hanging it.
Header and structural work
Keeping the opening you have costs less than widening it. A new header, sometimes sized by an engineer, adds lumber and framing time.
Frame material and glass
Aluminum, vinyl and wood-clad frames each come at a different price. Low-E coatings and tinted glass move the cost too.
Sill style
A flush sill gives you a level step onto the patio but takes more prep at the slab. A raised weather sill is simpler and sheds water well.
Stucco and finish work
Outside, most patching here means stucco. How much we cut and match, plus drywall and trim inside, changes the total.

Multi-Folding Door Questions

Something not covered here? (626) 654-3121

Can a folding door go in the opening my old slider uses?

In a lot of cases it can. Keeping the same width makes it mostly a swap, with new framing details at the sides and the sill. Going wider means we check the header and the wall first, then tell you what that adds to the job.

Do folding doors leak or let dust in?

A good door that is put in right should not. Most trouble traces back to a sill that is out of level or flashing that got skipped. We pan-flash the sill and seal the sides into the wall, which pays off in dry, windy weather when dust blows hard.

Do I need a permit?

Changing the size of an opening or the header usually calls for one. We pull the permit and handle the inspection. A same-size swap may need less, and we will tell you which applies to your job.

How long does the install take?

A straight swap often takes a day or two. Widening the opening with a new header and stucco work takes longer. You get the schedule with the estimate so you can plan around it.

Which way should the panels fold?

That depends on your furniture, the patio layout and where you want an everyday door. Many people choose a setup with one panel that swings like a regular door for quick trips outside. We go over the options when we visit.

Who does the installation?

Our own crew. We bring 30 years of window installation experience to every opening, and folding doors get the same care with level, square and seals.

Single-story stucco house with white-framed windows on both sides of a black glass entry door with sidelites, shrubs, curved walkway, and a toolbox and bucket on a drop cloth.

Ready to Open Up That Wall

We will look at the wall, measure and tell you plainly what a folding door takes in your home. We work in South San Jose Hills and nearby towns like West Covina, Hacienda Heights and La Puente.