
ServicesWindow Retrofitting
Window Retrofitting in South San Jose Hills
Our crew lifts out the worn sashes and glass but keeps the original frame and the stucco around it. A new vinyl unit gets fitted into that opening. Drafty aluminum sliders turn into quieter, tighter windows, and in most cases no wall needs patching or fresh paint.
How a retrofit works, and when to choose one
A retrofit, also called an insert window, leaves the original frame attached to the wall framing. We take out the moving parts: sashes, tracks and old glass. The new window has a flat exterior flange that laps over the old metal frame and seals to the stucco. Since nothing is cut from the wall, you avoid lath repair and paint touch-ups.
Plenty of houses in this area went up with single-pane aluminum windows set in stucco. The glass, rollers and weatherstrip wear out, but the frame underneath is often still sound. That is exactly where a retrofit fits best. When we find a frame that is bent, corroded or separating from the wall, we say so and walk you through full-frame window replacement for that opening.
We have run this business for 12 years, and the people fitting your windows carry 30 years of window installation experience. That history shows up in how carefully each opening gets measured and sealed.
What the retrofit work includes
Measuring every opening
Old frames are rarely square. We measure each one at the top, middle and bottom, side to side and up and down. The new window is built to the tightest reading so it sits flat without being forced.
Pulling the old sashes and track
We remove the glass panels, screws and bottom track. Then we scrape off old caulk and loose grit so the new frame has a clean surface to seal against.
Setting and shimming the new window
The new frame goes in plumb and level, shimmed at each screw point and fastened to the existing frame. We check that every sash slides and locks without a fight.
Sealing inside and out
Outside, a bead of sealant runs where the flange meets the stucco. Inside, gaps get low-expansion foam and a clean finish of trim or caulk.
Permit, haul-away and cleanup
When the job needs a county permit, we pull it and meet the inspector. Old windows leave on our truck, and we vacuum sills and floors before we go.

When your windows are due for a retrofit
- Windows that stick or come off the rails
- Old rollers flatten and aluminum tracks pit over the years, so the sash grinds or pops loose. Swapping rollers helps briefly, but on frames this old the worn track is usually the real issue.
- Rooms that bake in the afternoon
- One pane of glass does little to stop heat. When the west side of your home is still warm after sunset in summer, the windows are a large part of the cause.
- Air, dust and traffic noise getting in
- Loose sashes leave gaps you can feel when the wind picks up. New dual-pane units with fresh seals shut those gaps and quiet the room.
- Fogged glass and mildew on the sills
- Bare aluminum gets cold on winter mornings and drips with condensation. Year after year that water leaves dark spots on sills and stains the wall below.
- Walls you want left alone
- If your stucco is sound or was just painted, a retrofit updates the windows without disturbing the exterior finish.
What to expect from start to finish
- 1
Free in-home estimate
We visit, look over every window, check each frame for damage and take measurements. You get a written quote listing every opening with its style and glass. There is no sales pressure and no obligation to buy.
- 2
Ordering your windows
Once you say go, we order each window built to the measurements we took. If a permit is needed, we file for it while the windows are being made. We call you to set an install date when everything is in.
- 3
Install day
We put down drop cloths, then work one opening at a time so your home is never left wide open. Old sashes come out, new frames go in, and each one is shimmed, fastened and sealed inside and out.
- 4
Walk-through and cleanup
Before we leave, we open and lock every window with you and show you how the screens and latches work. Old windows go on our truck, floors and sills get vacuumed, and if there is a permit we schedule the final inspection.
What moves the price of a retrofit
Each window gets its own line on our written quote, so nothing is lumped together or hidden. Most of the total comes down to how many openings you have and how large they are. The rest depends on style, glass and what we find when we check the old frames.
- Window count and opening size
- Every opening is its own unit to build, carry in and seal, so the number of windows sets the base of the quote. Size matters too. A big living room slider or picture window takes more glass and more hands than a narrow bathroom window.
- Window style
- A fixed picture window is the simplest to build. Sliders, single-hung and casement units have more moving parts and hardware, and that shows up on the line for that opening.
- Glass choices
- Low-E coatings and dual panes are standard on our retrofits. Tempered safety glass is required by code near doors, tubs and some low openings, and obscure glass for bathrooms adds a little to those windows.
- Condition of the old frames
- If a frame is bent or pulling away from the wall, a retrofit will not seal right. We point it out at the estimate and price that opening as full-frame window replacement instead, so the change is on paper before work starts.
- Permit and access
- Some jobs need a county permit, and that fee is listed on the quote. Second-story windows, tight side yards or heavy plants in front of an opening can add time on the day.
Questions about window retrofitting
- Will I lose any glass with a retrofit?
- Yes, but only a thin band. Because the new frame nests inside the existing one, the visible glass shrinks slightly at the edges. Once the trim is done, most people stop seeing it. For a window you care about, like a view window, we can show you the before and after sizes at the estimate.
- How long does a retrofit job take?
- Most homes are done in one day. A typical window takes our crew an hour or two to pull, set and seal. Larger houses or a lot of big sliders can run into a second day, and we tell you that up front.
- Do I need a permit for retrofit windows?
- Often, yes. Many window changes in the county need a permit and a sign-off from the inspector. We are CSLB C-17 licensed, so we pull the permit ourselves and meet the inspector when it is time.
- Should I get a retrofit or full-frame replacement?
- If the old aluminum frames are straight and tight to the wall, a retrofit is usually the better call. It costs less and leaves your stucco alone. If frames are bent, rotted at the wood buck or leaking into the wall, full-frame window replacement fixes the real problem. We check every opening and tell you which one each needs.
- Do I have to be home, and how messy is it?
- Someone needs to let us in at the start and walk the job with us at the end. We lay drop cloths under each window and move small items out of the way. Old windows leave on our truck and we vacuum before we go.
- I already have a quote from another company. Can you beat it?
- Yes. We'll beat any estimate from another licensed contractor or USA-made window supplier. Have the other quote handy when we come out so we can compare the same windows and glass line by line.

Get a straight answer on your windows
We will look at your frames, tell you whether a retrofit is the right fit, and leave you with a written price. We work in South San Jose Hills and nearby towns like West Covina and Hacienda Heights.